ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º PCMCIA ETHERNET MANUAL INSTALLATION INSTRUCTIONS version 1.1C º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ The Ethernet adapter uses certain system resources to operate. The default system resources used for Ethernet are as follows: Adapter interrupt number IRQ=5, Shared memory address=D4000, Base I/O address=300. If other than the above default parameters are desired, they can be changed using the instructions which follow. IMPORTANT: If the system resources used by the Ethernet adapter are already in use by another device, the adapter will not function properly, and the system may be halted. As an example, if your system unit uses interrupt 5 for a mouse or a serial port, the Ethernet card will not work using the default settings and must be modified using the instructions below. There are two supported Network Operating Systems supported for this Ethernet card: ODI - For use with Novell Netware 3.11 and higher. NDIS - For use with NDIS compatible products such as LAN Support Program (LSP) and DOS LAN Requester (DLR). IMPORTANT: One of the two network operating systems MUST be installed on the workstation prior to installing this Ethernet Adapter. NOTE: Socket enablers are used when Card Services are not installed on a system. The purpose of the socket enablers provided on this diskette are to set up the connection between the PCMCIA card socket and the system bus. The enabler which is used will vary depending on your system and if Socket Services is present on your system. If card services is present, the adapter device driver (PCMDMCS.COM or PCMNICCS.DOS) will communicate with card services, and set up the slot automatically. * For information on the terms used in this document, see the "Glossary of Terms" section of this file. - 1 - ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º INSTALLATION OVERVIEW º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ OVERVIEW FOR INSTALLING IN A NETWARE 3.11 ENVIRONMENT ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The following instructions outline how to install the PCMCIA credit card adapter on a Netware network. For how to install this adapter in an NDIS environment, see the "Overview for installing with LAN Support Program (LSP) 3.3 " section which follows. Before beginning installation, make sure that the system resources needed by the Ethernet card (listed below) are free and do not conflict with other system devices. - Base I/O address default = 0x300 - Interrupt number (IRQ) default = 5 - Shared Memory Address default = 0xD400 If resource conflicts do exist, then the parameters in the NET.CFG file must be changed to eliminate them. See the "Netware ODI SHELL FOR DOS" booklet for setting these parameters, also see the sample NET.CFG file shown later in this text. In addition to modifying the NET.CFG, you must also change the parameters for the socket enabler (if used) to match those used in the NET.CFG. Help on changing these parameters later in this text. 1) Copy LSL.COM, IPXODI.COM and NETX.COM from the Netware 3.11 installation diskettes. These files can be copied to a sub directory or to the root. Please note that the latest NETX.COM file may be down loaded from the Novell BBS if not included with your Netware version. 2) Copy the adapter device driver PCMDMCS.COM and the NET.CFG file from the PCMCIA diskette into the same sub directory as in the previous step. 3a) If card services are present on system: Make sure the NET.CFG file has the key word PCMCIA. This tells the adapter device driver PCMDMCS.COM to use card services. 3b) If no card services are present on system: Using a text editor, remove the PCMICA statement in the NET.CFG file. Then copy the appropriate enabler (see below) from the PCMCIA diskette to the same sub directory mentioned in the above steps. If you have a system which uses the Intel 82365 controller chip, (most systems) Add the following statement to the beginning of your CONFIG.SYS: device=c:\path\pointeth.sys <ÄÄÄ Point enabler for Intel 82365 - Or if using a Toshiba PCMCIA controller chip: device=c:\path\tosheth.sys <ÄÄÄÄ Point enabler for SOME Toshiba systems - 2 - ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ OVERVIEW FOR INSTALLING IN A NETWARE 3.11 ENVIRONMENT (continued) ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 3b) continued - Or if you have a system which has Socket Services 1.01 only: device=c:\path\ethernet.sys <ÄÄÄÄ Socket Services 1.01 enabler 4) Power down the system unit and insert credit card adapter, attach the Media Access Module (cable) to the card and to the network. 5) Power up system unit, Make sure there are no error messages from the IBM credit card enabler (if used) or adapter device driver during boot up. 6) From the DOS prompt in the sub directory containing the below files, execute them by typing the following: LSL.COM ( Netware Layer Support Link program ) PCMDMCS.COM ( PCMCIA Ethernet adapter device driver ) IPXODI.COM ( Netware ODI Network driver ) NETX.COM ( Netware workstation shell ) The words "ATTACHED TO SERVER" should appear at this point. After successful completion of these commands, you may want to include them into your AUTOEXEC.BAT file for automatic execution. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ OVERVIEW FOR INSTALLING WITH LAN SUPPORT PROGRAM (LSP) 3.3 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The following instructions outline how to install the PCMCIA credit card adapter in an NDIS environment. For how to install this adapter in an Novell environment, see the "Overview for installing in a Novell environment" section which precedes this one. Before beginning installation, make sure that the system resources needed by the Ethernet card (listed below) are free and do not conflict with other system devices. - Base I/O address default = 0x300 - Interrupt number (IRQ) default = 5 - Shared Memory Address default = 0xD400 If resource conflicts do exist, then the parameters in the PROTOCOL.INI file must be changed to eliminate them. See the "Modifying Resource Settings" section later in this text. In addition to modifying the PROTOCOL.INI file, you must also change the parameters for the socket enabler (if used) to match those used in the PROTOCOL.INI. Help on changing these parameters can be found later in this text. 1) Install LSP version 3.3 (or later) using the DXMAID.EXE installation aid. 2) Indicate that you do have an adapter option diskette. - 3 - ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ OVERVIEW FOR INSTALLING WITH LAN SUPPORT PROGRAM (LSP) 3.3 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 3) When prompted by LSP to place the option diskette in the floppy drive, place the PCMCIA Ethernet diskette in the drive and press enter. LSP is uses the information file PCMNICCS.NIF to build a PROTOCOL.INI file in the LSP install directory. 4) Copy the adapter device driver PCMNICCS.DOS file from the PCMCIA diskette same sub directory as in the previous step. 5a) If card services are present on system: Make sure the PROTOCOL.INI file has the key word PCMCIA in it. This tells the adapter device driver PCMNICCS.DOS to use card services. 5b) If no card services are present on system: Using a text editor, remove the PCMICA statement (if present) from the PROTOCOL.INI file. Then copy the appropriate enabler (see below) from the PCMCIA diskette to the same sub directory mentioned in the above steps. If you have a system which uses the Intel 82365 controller chip, (most systems) Add the following statement to the beginning of your CONFIG.SYS: device=c:\path\pointeth.sys <ÄÄÄ Point enabler for Intel 82365 - Or if using a Toshiba PCMCIA controller chip: device=c:\path\tosheth.sys <ÄÄÄÄ Point enabler for SOME Toshiba systems - Or if you have a system which has Socket Services 1.01 only: device=c:\path\ethernet.sys <ÄÄÄÄ Socket Services 1.01 enabler 6) Power down the system unit and insert credit card adapter, attach the Media Access Module (cable) to the card and to the network. 7) Power up system unit, Make sure there are no error messages from the IBM credit card enabler (if used) or adapter device driver during boot up. 8) You must now install a network shell such as DOS LAN Requester. - 4 - ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º MODIFYING RESOURCE SETTINGS º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ The following steps describe how to modify files for using other than the PCMCIA Ethernet card defaults. See the "SAMPLE CONFIGURATION FILES" section for more detail. Note that if an enabler is used, its parameters must match those of their corresponding PROTOCOL.INI or NET.CFG file (see "Changing Enabler Parameters). IBM's LAN Support Program and Microsoft LAN Manager will create the PROTOCOL.INI file for you using the adapter default values. All you need to do is change these values as desired using a text editor. You must also modify the enabler parameters (if used) to reflect the same values in the PROTOCOL.INI file. For an NDIS installation, edit the PROTOCOL.INI file to reflect the following entries: "PCMNICCS_NIF" {modify parameters after this line} IOBASE = value {values from list below} INTERRUPT = value {values from list below} RAM = value {values from list below} DRIVERNAME = PC-NIC$ {this line must be added} See the "Sample Configuration Files" section for an example of the PROTOCOL.INI file. IOBASE = value Where value is any base I/O address between 0x120 and 0xC30 in increments of 20 hex (32 decimal). For example, valid address include: 120, 140, 160 and so on... The driver default value is 0x300 if no keyword is supplied. The leading "0x" for hex notation is required. INTERRUPT = value Where value is one of the following interrupts, 3, 4, 5, 7, 9, 10, 11 The driver default value is 5 if no keyword is supplied. RAM = value where value is one of the following memory segment addresses: 0xC800, 0xCC00, 0xD000, 0xD400, 0xD800, 0xDC00 The driver default value is 0xD400 if no keyword is supplied. The leading "0x" for hex notation is required. The above address are recommended because of their general availability, however most I/O ports, IRQ's and Memory locations can be used for the PCMCIA Ethernet adapter as long as it is not in use by another device. - 5 - ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º MODIFYING RESOURCE SETTINGS (continued) º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ For NetWare installation, modify the NET.CFG file to reflect the following entries: Link Driver PCMDMCS {modify parameters after this line} PORT = value {values from list below} INT = value {values from list below} MEM = value {values from list below} The NET.CFG file must be included in the system path statement. For the NetWare DOS ODI driver, the following parameter restrictions apply: PORT value (default is 300) where value is one of the following base I/O addresses, without the trailing 'h': 200h, 220h, 240h, 260h, 280h, 2A0h, 2C0h 300h, 340h, 380h INT value (default is 5) where value is one of the following interrupts, 3, 4, 5, 7, 9, 10, 11, 15 MEM value [range] (default is D4000) where value is one of the following memory addresses, without the trailing 'h': C0000h, C4000h, C8000h, CC000h D0000h, D4000h, D8000h, DC000h The above address are recommended because of their general availability, however most I/O ports, IRQ's and Memory locations can be used for the PCMCIA Ethernet adapter as long as it is not in use by another device. - 6 - ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ CHANGING DEFAULT PARAMETERS FOR ENABLERS ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Choose from one of the two below depending on network type: PCMNICCS.DOS <ÄÄÄÄ Ethernet adapter driver for NDIS (LSP). PCMDMCS.COM <ÄÄÄÄ Ethernet adapter driver for ODI (Netware 3.11). ET0.MSG <ÄÄÄÄ Error message file. This file is used by the enabler when an error is encountered. This file is required and has to be installed in the same sub directory as the enabler. Choose one of the three enablers below depending on system environment: POINTETH.SYS <ÄÄÄÄÄÄ Intel * 82365 PCMCIA controller point enabler. Use this enabler if Socket Services is not available and if your system uses the Intel 82365 PCMCIA controller chip. This enabler should be used if you are unsure of your system setup. The optional parameters are: IRQ=X SA DS=XX SRAM=XXXX IO=XXX ETHERNET.SYS <ÄÄÄÄÄÄ Socket Services 1.01 enabler. Use this enabler if Socket Services is present on your system unit and Card services is not. The optional parameters are: IRQ=X SA DS=XX SRAM=XXXX IO=XXX TOSHETH.SYS <ÄÄÄÄÄÄ Toshiba T3300SL PCMCIA controller point enabler. Use this enabler if your system is a Toshiba T3300SL. The optional parameters are: IRQ=X SA DS=XX SRAM=XXXX IO=XXX - 7 - ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ CHANGING DEFAULT PARAMETERS FOR ENABLERS (continued) ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ For systems without Card Services which use the Intel 82365 PCMCIA controller chip (most systems), insert the following statement at the beginning of your systems CONFIG.SYS file: ÚÄÄÄÄÄÄÄ Socket enabler for Intel 82365 PCMCIA (for ³ most systems) ÄÄÄÄÄÁÄÄÄÄÄ DEVICE=C:\PATH\POINTETH.SYS IRQ=5 SA DS=16 SRAM=D400 IO=300 ÄÂÄ ÄÂÄ ÄÂÄ ÄÄÂÄÄ ÄÂÄ ³ ³ ³ ³ ÀÄÄÄ I/O Port 300 ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄ Memory pos D400 ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Data Size 16 bit ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Use Socket 'A' ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Use Interrupt 5 The above example shows the enabler using all of the default parameters. The same results would be achieved by leaving off all the parameters off, like this: DEVICE=C:\POINTETH.SYS Enabler options must be equivalent to the parameters that were placed in the PROTOCOL.INI or NET.CFG file. If the NDIS driver is to be used, insert the following statement in the CONFIG.SYS file. DEVICE=C:\PATH\PCMNICCS.DOS IMPORTANT: This statement should immediately follow the line that invokes the Protocol Manager program (DEVICE=C:\PATH\PROTMAN.DOS ). See the "Sample Configuration Files" section of this text. If the Novell NetWare driver is being installed, insert the driver following LSL at the end of the AUTOEXEC.BAT file as shown in the example below: LSL PCMDMCS IPXODI NETX (or NET3 or NET4 or NET5 or BNETX or ...) LOGIN Consult Novell documentation for more information on these files. - 8 - ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º SAMPLE CONFIGURATION FILES USING NETWARE 3.11 (ODI) º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Sample CONFIG.SYS file using Novell Netware 3.11 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ FILES=30 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Socket enabler (Change, depending on System) BUFFERS=10 ÄÄÄÄÄÁÄÄÄÄÄ DEVICE=C:\NET\POINTETH.SYS IRQ=5 SA DS=16 SRAM=D400 IO=300 LASTDRIVE=E: ÄÂÄ ÄÂÄ ÄÂÄ ÄÄÂÄÄ ÄÂÄ ³ ³ ³ ³ ÀÄÄÄÄÄÄÄÄ I/O Port 300 ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Memory pos D400 ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Data Size 16 bit ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Use Socket 'A' ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Use Interrupt 5 The above example shows the enabler using all of the default parameters. The same results would be achieved by leaving off all the parameters off, like this: DEVICE=C:\POINTETH.SYS ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Sample AUTOEXEC.BAT file using Novell Netware 3.11 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ PROMPT=$P$G PATH=C:\DOS;C:\NETWARE; SET TEMP=C:\DOS LSL <ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Novell Link Support Layer. PCMDMCS <ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Ethernet Adapter Driver for ODI (Novell). IPXODI <ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Novell IPX Protocol Driver. NETX <ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Novell Workstation Shell. F:LOGIN ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Sample NET.CFG file for Netware 3.11 (ODI) ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Link Driver PCMDMCS PORT 300 INT 5 MEM D4000 FRAME ETHERNET_802.3 PCMCIA <ÄÄÄÄÄÄÄÄÄÄÄÄ Use this statement only if card services is present. Please note that the parameters in this file must match the options for the enabler (if used) in the CONFIG.SYS file which would be as follows: DEVICE=C:\POINTETH.SYS IRQ=5 SRAM=D400 IO=300 - 9 - ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º SAMPLE CONFIGURATION FILES USING LAN SUPPORT PROGRAM (NDIS) º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Sample CONFIG.SYS file using LAN Support Program Version 1.3 (LSP) ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ FILES=30 BUFFERS=10 DEVICE=C:\POINTETH.SYS <ÄÄÄÄÄÄÄÄ Socket enabler (change depending on system). DEVICE=C:\LSP\PROTMAN.DOS /I:\LSP DEVICE=C:\LSP\PCMNICCS.DOS <ÄÄÄÄÄÄÄÄ Ethernet Adapter Driver for NDIS (LSP). DEVICE=C:\LSP\DXMA0MOD.SYS 001 DEVICE=C:\LSP\DXME0MOD.SYS DEVICE=C:\LSP\DXMT0MOD.SYS O=ON LASTDRIVE=Z: ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Sample AUTOEXEC.BAT file using LAN Support Program Version 1.3 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ \LSP\NETBIND <ÄÄÄÄÄÄÄÄÄÄÄÄ Added during LSP install (Required) PROMPT=$P$G PATH=C:\DOS;C:\LSP; SET TEMP=C:\DOS From here down are DOS LAN Requestor statements @ECHO OFF <ÄÄÄÄÄÄÄÄ that were added during the DLR installation, YNPROMPT Y N 30 Start DOS LAN Requester (Y/N)? IF ERRORLEVEL 1 GOTO NODLR NET START IF ERRORLEVEL 1 GOTO NODLR CALL INITFSI.BAT :NODLR - 10 - ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Sample PROTOCOL.INI file for LSP. ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ [PROTMAN_MOD] DriverName = PROTMAN$ [DXMAIDXCFG] DXME0_NIF = DXME0.NIF DXMJ0MOD_NIF = DXMJ0MOD.NIF PCMNICCS_NIF = PCMNICCS.NIF PCMNICCS2_NIF = PCMNICCS.NIF IBMTOK_NIF = IBMTOK.NIF IBMTOK2_NIF = IBMTOK.NIF SMCDOSJP_NIF = SMCDOSJP.NIF SMCDOSJP2_NIF = SMCDOSJP.NIF SMCDOSAT_NIF = SMCDOSAT.NIF SMCDOSAT2_NIF = SMCDOSAT.NIF SMCDOSMC_NIF = SMCDOSMC.NIF SMCDOSMC2_NIF = SMCDOSMC.NIF [DXME0_NIF] <ÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ DriverName = DXME0$ ³ ³ Bindings = PCMNICCS_NIF ³ These statements define the system ³ [PCMNICCS_NIF] ³ resources used by the Ethernet ³ ;PCMCIA Ethernet Adapter ³ adapter. Some will be added for you ³ DriverName = PCM-NIC$ ³ during LSP installation. ³ IOBASE = 0X300 ³ ³ INTERUPT = 5 ³ ³ RAM = 0XD400 <ÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ PCMCIA <ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ In this particular case, card services is present and this parameter is necessary. Please note that the parameters in this file must match the options for the enabler in the CONFIG.SYS file which would be as follows: DEVICE=C:\POINTETH.SYS IRQ=5 SRAM=D400 IO=300 - 11 - ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º GLOSSARY OF TERMS º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ¯ IRQ (Also referred to as Interrupt) An electronic Signal used by hardware (such as a network card) to interrupt your CPU (get its attention). Each device in your system must use a separate IRQ in order to work properly. IRQ 5 is most commonly use for Ethernet cards, IRQ 3 is also sometimes used. Below is a list of interrupts and the devices for which they are commonly used. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ IRQ DEVICE ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 2 (9) EGA/VGA Token Ring adapters 3 Generally available unless used for bus mouse 4 COM1, COM3 5 Generally available unless used for LPT2 6 Floppy disk controller 7 Parallel port LPT1 8 Real Time clock 10 Generally available 11 Generally available 12 Mouse (for PS/2) 13 Math coprocessor 14 Hard disk controller 15 Generally available ¯¯¯ BASE I/O PORT ®®® The base input/output port specifies a channel through which information is transferred between your hardware (such as a network card) and your computer's CPU. The port appears to your CPU as an address (in hex). Each hardware device in your computer must use a different base I/O port number. The PCMCIA Ethernet adapter uses a 32 byte I/O port address which equates to 20 in hexadecimal. This is important when assigning the port address. - 12 - ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º GLOSSARY OF TERMS (continued) º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Below is a list of base I/O ports and the devices which commonly use them. The ports listed without a device are normally free to use for your system. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ PORT DEVICE PORT DEVICE ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 200 to 20F Game port 300 to 30F <- PCMCIA Ethernet card default 210 to 21F 310 to 31F <- also includes this address. 220 to 22F 320 to 32F Hard disk controller 230 to 23F Bus Mouse 330 to 33F 240 to 24F 340 to 34F 250 to 25F 350 to 35F 260 to 26F 360 to 36F 270 to 27F LPT3 370 to 37F LPT2 280 to 28F 380 to 38F 290 to 29F 390 to 39F 2A0 to 2AF 3A0 to 3AF 2B0 to 2BF 3B0 to 3BF LPT1 2C0 to 2CF 3C0 to 3CF EGA/VGA 2D0 to 2DF 3D0 to 3DF CGA/MCGA and EGA/VGA (color modes) 2E0 to 2EF 3E0 to 3EF 2F0 to 2FF COM2 3F0 to 3FF Floppy disk controller; COM1 ¯¯¯ BASE MEMORY ADDRESS ®®® (also referred to as the RAM Start Address) The base memory address defines the address of the region in your computer's memory to be used by the network card to exchange information between your computer and the others on the network. ¯¯¯ CARD SERVICES ®®® The highest layer of software which controls 1 or more PCMCIA sockets. Card services manages your systems resources to prevent system conflicts. For example, if a card is inserted into the slot, it can request IRQ 5 for use. The request comes up through Socket services to card services. Card services knows that IRQ 5 is already in use by another device and denies the use of this resource but offers different IRQ for use. This arbitration continues until the card requesting resources is satisfied or system resources are exhausted. - 13 - ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º GLOSSARY OF TERMS (continued) º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ CARD SERVICES ³<ÄÄÄÄÄÄ>³ SYSTEM RESOURCES ³ ÀÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÙ ³ IRQ's MEM, I/O PORTS ³ ÚÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄ¿ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³ SOCKET SERVICES ³ ÀÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÙ ÚÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³PCMCIA CONTROLLER CHIP³<ÄÄÄÄÄÄ ³ POINT ENABLER ³ ÀÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÚÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄ¿ A point enabler sets up slot ³ PCMCIA 68 PIN SLOT ³ by communicating directly ÀÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÙ to controller chip if card ÚÄÄÄÄÄÁÄÄÄÄÄÄ¿ services is not available. ³ PCMCIA CARD³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÙ ¯¯¯ ENABLER ®®® Socket enablers are used when Card Services are not installed on a system. The purpose of the socket enablers provided on this diskette are to set up the connection between the PCMCIA card socket and the system bus. The enabler which is used will vary depending on your system and if Socket Services is present on your system. If card services is present, the adapter device driver (PCMDMCS.COM or PCMNICCS.DOS) will communicate with card services, and set up the slot automatically. The "Point Enabler" included with this diskette communicates directly with the Intel 82365 PCMCIA controller chip at its lowest level in order to open a path between the PCMCIA slot and the system bus. Once this path is set up, the adapter device driver (PCMDMCS.COM for NetWare or PCMNICCS.DOS for NDIS) acts the same as if the adapter were installed in full size adapter. ¯¯¯ PCMCIA ®®® Personal Computer Memory International Association A standard which defines the interface between a 68 pin socket and one of the following system buses: ISA, EISA, MCA. This standard allows the use of very small (credit card size) cards for such purposes as adding RAM, Flash RAM (used as file storage), Input output devices such as Modems and LAN connections. Some of the benefits of PCMCIA are: - Allows easy access to the system bus. No need to remove system cover. - Allows the sharing of cards between systems. - Eliminates the incompatibility between busses, the same card can be used in an ISA, EISA or MCA system as long as the card and system comply with the standard. - 14 - ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º INSTALLATION DISKETTE CONTENTS º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ This installation diskette includes the following files: DOS 2-09-93 4:12p NDIS subdirectory ³ ÃÄÄÄ> PCMNICCS DOS 17705 6-02-93 8:11a NDIS device driver ÃÄÄÄ> PCMNICCS NIF 2254 7-06-93 10:01a NDIS network information file ÀÄÄÄ> PROTOCOL INI 160 5-19-93 8:40a Example of text DE0 MSG 2702 8-02-93 11:21a Diagnostics messages ECCTEST EXE 20494 8-02-93 11:56a Diagnostic program READ ME 23553 8-02-93 12:45p Information for Ethernet ET0 MSG 535 8-02-93 3:28p ETHERNET.SYS enabler messages ECCDIAG EXE 50649 7-01-93 3:22p Diag pgrm (called from ECCTEST.EXE) POINTETH SYS 6637 7-08-93 1:23p Hardware enabler for Intel 82365 TOSHETH SYS 5938 10-20-92 6:25p Toshiba 3300 hardware enabler OEMSETUP INF 736 8-02-93 1:54p Workgroup for Windows setup file PCMDMCS COM 26547 6-17-93 3:01p ODI Device Driver ETHERNET SYS 8280 11-11-92 5:53p Socket Services 1.01. enabler INSTALL TXT 32228 9-20-93 12:00p Install instructions (this file) NET CFG 164 9-15-93 10:05a Sample NET.CFG file - 15 -