BusLogic Device Driver Installation for NeXTSTEP 3.2
====================================================

Files
-----

The following files are included in this package:

	next32dd.Z	- Compressed 'dd' image of BusLogic Driver
			  diskette (3.5" format)

	readme.txt	- This readme file


Unpacking Procedure
-------------------

1.  On a Unix system, decompress "next32dd.Z" as follows:

	# uncompress next32dd.Z

2.  The resulting file, "next32dd" is a 'dd' image of the BusLogic
    driver diskette (3.5" format).  Insert a blank 3.5" format
    diskette in the floppy drive, and type:

	# dd if=next32dd of=/dev/rfd0b bs=9k	(on NextStep)

		or

	# dd if=next32dd of=/dev/rfd0 bs=9k	(on other Unix systems)

    The BusLogic Device Driver diskette is now created.


Installation Procedure
----------------------

1.  Configure BusLogic SCSI Host Adapter I/O port address to 0x334.
 
2.  Boot system from the NeXTSTEP 3.2 Installation diskette.
 
3.  The boot procedure will load the device drivers from the
    Installation diskette and display the following:
 
	The following SCSI adapter and hard disk controller device
	drivers are available while installing NEXTSTEP:

	...

	If you have a different kind of SCSI adapter or hard disk
	controller, insert the floppy disk that contains the device
	driver for your device.

	Type 1 to load a device driver from the disk in the floppy disk drive.
	Type 2 to continue without loading additional device drivers.

	--->

    Insert the BusLogic Device Driver diskette and select option 1.

4.  After reading the diskette for a few seconds, the following is
    displayed:

	The floppy disk in the drive contains the following SCSI adapter and
	hard disk controller device drivers:

	1.  BusLogic SCSI Adapter

	Type the number for the device driver you want to install.
	Type 2 to continue without installing a device driver from this disk.

	--->

    Select 1 to load the BusLogic device driver.

5.  The screen displays a series of progress messages.  Press Return
    when "The driver was loaded successfully" message is displayed.
 
6.  The SCSI adapter device driver option prompt from step 3
    redisplays with the BusLogic SCSI Adapter entry.  Select option
    2 to continue without loading additional device driver.
 
7.  Continue installation until you are asked to eject the floppy
    to reboot from the hard disk.  At this point, re-insert the
    Installation diskette instead and reboot using this diskette.
 
8.  At the boot prompt, type the following:

	boot:  mach_kernel -s "Boot Drivers=PS2Keyboard"

9.  Repeat steps 3-6 and continue installation until the shell prompt,
    "#", is displayed.
 
10. With the BusLogic Device Driver diskette still in the floppy
    drive, type the following:

	# /usr/etc/driverLoader D=Floppy
	# mount -n /dev/sd0a /disk
	# mount -n /dev/fd0a /floppy
	# cp -r /floppy/usr/Devices/BusLogic.config /disk/usr/Devices
	# umount /floppy

    Eject the diskette from the floppy drive and type:

	# reboot

    Reboot from the hard disk and continue installation according to
    the Installation Manual.


To reach us & the latest drivers and information:

Tech Support:   (408) 654-0760
FAX:            (408) 492-1542
BBS:            (408) 492-1984 (14.4k, N81)
Email:          techsup@buslogic.com
FTP Site:       ftp.buslogic.com (204.160.180.11)
WWW Page:       http://www.buslogic.com