& F=                     E V - 1 5 8 A                                                                                                          Version 1.1                                                                                                ( C ) C o p y r i g h t E v e r e x S y s t e m s , I n c . 1 9 8 7                                                                                      L o a d i n g p r o g r a m , p l e a s e w a i t . . . _                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      x @2 H E L P I D 0 0 0 1 P a g e 0 1 o f 0 1                                                                                                   Select 'Y' if you are going to install the      card into your system.                                                                          Use the [F5] and [F6] function keys to          make your selections.                                                                                                                                                                                                                                                                         F 1 E X I T H E L P x @2 H E L P I D 0 0 0 2 P a g e 0 1 o f 0 1                                                                                                   Use the [F5] and [F6] function keys to          select the current size of extended memory      in kilobytes.  This value has to be a           multiple of 128K and it ranges from             0K - 15232K.                                                                                                                                                                                                                                                                                  F 1 E X I T H E L P x @2 H E L P I D 0 0 0 3 P a g e 0 1 o f 0 1                                                   Use the [F5] and [F6] function keys to          select how much memory you want to allocate     as extended memory. The amount of memory        not assigned as extended memory will            automatically become EMS memory. If             you do not want the leftover memory to          become EMS memory, please disable the           EMS I/O ports. If you do not want any           extended memory, select "0".                                                                                                                  F 1 E X I T H E L P x @2 H E L P I D 0 0 0 4 P a g e 0 1 o f 0 1                                                                                                   Select the amount of total memory you           have on this card. Each bank provides           2 megabytes of memory.                                                                                                                                                                                                                                                                                                                                                                        F 1 E X I T H E L P x @2 H E L P I D 0 0 0 5 P a g e 0 1 o f 0 2                                                  Valid values for the EMS I/O port addresses     are: 208H, 218H, 258H, 268H, 2A8H, 2B8H,        and 2E8H.                                                                                       If your board has up to 2MB available for       EMS memory, select 1 EMS I/O port address.                                                      If your board has up to 4MB available for       EMS memory, select 2 sequential EMS port        addresses.                                                                                     F 1 E X I T H E L P C t r l - P g D n N e x t P a g e H E L P I D 0 0 0 5 P a g e 0 2 o f 0 2                                                   If your board has up to 6MB available for       EMS memory, select 3 sequential EMS port        addresses.                                                                                      If your board has up to 8MB available for       EMS memory, select 4 sequential EMS port        addresses.                                                                                      NOTE: Use [F5] and [F6] keys to select the            EMS I/O port address. Each EMS I/O              port requires its own port address.     F 1 E X I T H E L P C t r l - P g U p L a s t P a g e x @2 H E L P I D 0 0 0 6 P a g e 0 1 o f 0 1                                                                                                  Press F5 to start the test. Each bank will      be tested sequentially and the status of        the memory chips will be displayed on the       screen (bad chip(s) will blink). If there       are any blinking chips, make sure you check     each blinking chip to see if there are any      broken or bent pins. Check also if the chip     is improperly oriented (notch on chip must      face to the left of board).                                                                    F 1 E X I T H E L P x @2 H E L P I D 0 0 0 7 P a g e 0 1 o f 0 1                                                                                                   Select the amount of existing base              memory on your system. The system               will fill the base memory up to 640K            for you if your base memory is less than        640K. If you do not increase the size of        base memory, select 'No' on the question        "Fill Base Up To 640K: " .                                                                                                                                                                    F 1 E X I T H E L P x @2 H E L P I D 0 0 0 8 P a g e 0 1 o f 0 1                                                                                                   Some systems are too fast to run EMS on         16-bit mode. You may try 16-bit mode first;     if it does not work, then try 8-bit mode.                                                                                                                                                                                                                                                                                                                                                     F 1 E X I T H E L P x @2 H E L P I D 0 0 0 9 P a g e 0 1 o f 0 1                                                                                                   Select 'YES' if you want to enable the          parity checking on your system.                                                                                                                                                                                                                                                                                                                                                                                                               F 1 E X I T H E L P x @2 H E L P I D 0 0 1 0 P a g e 0 1 o f 0 1                                                   You may save your current settings on a         configuration file.  Please enter the           name of the configuration file and press        F8 to save the file.  To reload the setting     from a configuration file, enter the file       name and press F9.                                                                                                                                                                                                                                                                            F 1 E X I T H E L P x @2 H E L P I D 0 0 1 1 P a g e 0 1 o f 0 1                                                                                                   Select 'Yes' if you want to fill memory from    this board to your base memory up to 640K.      For example, if you have 512K memory on         your mother board, the amount of base filled    is 128K.                                                                                        Select 'No' if you do not increase the size     of the base memory on your system.                                                                                                            F 1 E X I T H E L P