旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴커 � Hard Disk Tech Specs(tm) v3.0 � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴켸 Hard Drive Solutions Family(tm)  //IO-3100 01 D86, 82, 95, 82 D95, 82, 95, 60 D95, 60, 86, 60 D86, 60, 86, 82 T95, 72, 0, 1, C1 C70, 93, 1, 0 T75, 91, 0, 1, C2 C15, 93, 1, 0 T20, 91, 0, 1, C3 T8, 91, 0, 1, C4 T34, 91, 0, 1, J1 J3 J4 T72, 86, 0, 1, J5 T78, 58, 0, 1, J6 T60, 91, 0, 1, J8 J7 { Drives: 7 SCSI devices supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). C1 External SCSI connector. C2 Internal SCSI connector. C3 Floppy connector. C4 LED connector. J1 Closed (Default) Floppy controller enabled. Open Floppy controller disabled. J3 Open (Default) Precomp = 125ns. Closed Precomp = 187ns. J4 Open (Default) Single-speed floppies installed. Closed Dual-speed floppies installed. J5 ooo BIOS address C:4000 - C:7FFF. ooo ooX BIOS address C:8000 - C:BFFF. ooX oXo BIOS address C:C000 - C:FFFF. oXo oXX BIOS address D:0000 - D:3FFF. oXX Xoo BIOS address D:4000 - D:7FFF. Xoo XoX BIOS address D:8000 - D:BFFF. XoX XXo (Default) BIOS address D:C000 - D:FFFF. XXo J6 Open Logic ground (MUST remain open). J7 Closed Termination power enabled. Open (Default) Termination power disabled. J8 1-2 Closed External and internal power source for on board terminators. 2-3 Closed (Default) Internal power source for on board terminators. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //IO-3120 01 C25, 93, 1, 0 T30, 91, 0, 1, J1 C64, 93, 1, 0 T69, 91, 0, 1, J2 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J3 T66, 80, 0, 1, Term. Term. T20, 91, 0, 1, W1 T42, 91, 0, 1, W2 W3 W4 W5 W6 T85, 93, 0, 4, W7 T88, 93, 0, 4, W8 T81, 58, 0, 1, W9 T78, 85, 0, 1, F1 { Drives: 7 SCSI devices supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 Floppy connector. J2 Internal SCSI connector. J3 External SCSI connector. F1 Fuse. W1 Open Floppy controller disabled. Closed (Default) Floppy controller enabled. W2 -1 Open Floppy IRQ 10. -2 Closed Closed (Default) Floppy IRQ 6. Open -3 Closed (Default) Floppy DMA channel 2. -4 Open -5 Closed -6 Open -3 Open Floppy DMA channel 3. -4 Closed -5 Open -6 Closed W3 1-6 Open BIOS address C:4000 - C:BFFF. 2-5 Open 3-4 Open Open BIOS address C:8000 - C:BFFF. Open Closed Open BIOS address C:C000 - C:FFFF. Closed Open Open BIOS address D:0000 - D:3FFF. Closed Closed Closed BIOS address D:4000 - D:7FFF. Open Open Closed BIOS address D:8000 - D:BFFF. Open Closed Closed (Default) BIOS address D:C000 - D:FFFF. Closed Open W4 1-2 Open Factory use. 2-3 Closed Factory use. Leave closed. W5 1-2 Closed Factory use. Leave closed. 2-3 Open Factory use. W6 Open (Default) Primary floppy I/O ports (3F0 - 3FF). Closed Secondary floppy I/O ports (370 - 37F). W7 1-2 Closed External and internal power source for on board terminators. 2-3 Closed (Default) Internal power source for on board terminators. W8 Closed (Default) Termination power enabled. Open Termination power disabled. W9 Open Logic ground (MUST remain open). Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //IO-3200 00 D86, 82, 95, 82 D95, 82, 95, 60 D95, 60, 86, 60 D86, 60, 86, 82 T95, 72, 0, 1, J1 C80, 80, 1, 1 T79, 84, 0, 1, J2 T70, 65, 0, 1, Term. T70, 61, 0, 1, Term. T58, 92, 0, 1, W1 T65, 95, 0, 4, W2 T77, 95, 0, 4, W3 T81, 95, 0, 4, W4 T84, 95, 0, 4, W5 T87, 95, 0, 4, Fuse { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. Fuse Thermal fuse. W1 ooo BIOS address C:4000 - C:7FFF. ooo ooX BIOS address C:8000 - C:BFFF. ooX oXo BIOS address C:C000 - C:FFFF. oXo oXX BIOS address D:0000 - D:3FFF. oXX Xoo BIOS address D:4000 - D:7FFF. Xoo XoX BIOS address D:8000 - D:BFFF. XoX XXo (Default) BIOS address D:C000 - D:FFFF. XXo W2 1-2 U7 contains RAM. 2-3 (Default) U7 contains an EPROM. W3 1-2 External and internal power source for on board terminators. 2-3 (Default) Internal power source for on board terminators. W4 Closed (Default) Termination power enabled. Open Termination power disabled. W5 Open Logic ground (MUST remain open). Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //IO-2010 21 C70, 92, 1, 0 T75, 90, 0, 1, C1 C18, 92, 1, 0 T23, 90, 0, 1, C2 T15, 80, 0, 1, C9 T42, 92, 0, 4, J1 T42, 90, 0, 1, J2 J3 T53, 92, 0, 4, J4 T56, 92, 0, 4, J5 T59, 92, 0, 4, J6 T62, 92, 0, 4, J7 T65, 92, 0, 4, J8 T68, 92, 0, 4, J10 { Drives: 2 IDE (AT) drives supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). C1 Floppy connector. C2 IDE interface connector. C9 LED connector. J1 Open (Default) I/O CHRDY connectoed to AT bus. Closed I/O CHRDY not connected to AT bus. J2 All open (Default) DMA REQ disabled. 1-6 DMA REQ 5. 2-5 DMA REQ 6. 3-4 DMA REQ 7. J3 All open (Default) DMA ACK disabled. 1-6 DMA ACK 5. 2-5 DMA ACK 6. 3-4 DMA ACK 7. J4 Open (Default) DMA ACK connected to AT bus. Closed DMA ACK not connected to AT bus. J5 Open (Default) Primary HD I/O ports (1F0 - 1F7) and primary floppy I/O ports (3F0 - 3F7). Closed Secondary HD I/O ports (170 - 177) and secondary floppy I/O ports (370 - 377). J6 1-2 Host system has a Phoenix BIOS. 2-3 (Default) Host system has IBM, Award, AMI, or other BIOS. J7 Open Do not change this jumper. J8 Open Floppy controller disabled. Closed (Default) Floppy controller enabled. J10 Open Zero wait state. Closed (Default) Back-to-back I/O delay (necessary for 25 - 30 MHz systems with a fast bus - has no effect on slower systems). } * //IO-2020 21 C70, 92, 1, 0 T75, 90, 0, 1, C1 C18, 92, 1, 0 T23, 90, 0, 1, C2 C70, 85, 1, 0 T75, 83, 0, 1, C3 T15, 80, 0, 1, C9 T42, 92, 0, 4, J1 T42, 90, 0, 1, J2 J3 T53, 92, 0, 4, J4 T56, 92, 0, 4, J5 T59, 92, 0, 4, J6 T62, 92, 0, 4, J7 T65, 92, 0, 4, J8 T68, 92, 0, 4, J10 T68, 85, 0, 4, J11 T65, 85, 0, 4, J12 T62, 85, 0, 4, J13 { Drives: 2 IDE (AT) drives supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). C1 Primary connector. C2 IDE interface connector. C3 Secondary floppy connector. C9 LED connector. J1 Closed (Default) I/O CHRDY connectoed to AT bus. Open I/O CHRDY not connected to AT bus. J2 All open (Default) DMA REQ disabled. 1-6 DMA REQ 5. 2-5 DMA REQ 6. 3-4 DMA REQ 7. J3 All open (Default) DMA ACK disabled. 1-6 DMA ACK 5. 2-5 DMA ACK 6. 3-4 DMA ACK 7. J4 Closed (Default) DMA ACK connected to AT bus. Open DMA ACK not connected to AT bus. J5 Open Enable ATA hard disk mode. Closed Enable ATA tape drive mode. J6 1-2 Host system has a Phoenix BIOS. 2-3 (Default) Host system has IBM, Award, AMI, or other BIOS. J7 Open Do not change this jumper. J8 Open Floppy controller disabled. Closed (Default) Floppy controller enabled. J10 Open Zero wait state. Closed (Default) Back-to-back I/O delay (necessary for 25 - 30 MHz systems with a fast bus - has no effect on slower systems). J11 Open (Default) Primary floppy I/O ports (3F0 - 3F7). Closed Secondary floppy I/O ports (370 - 377). J12 Open (Default) Primary HD I/O ports (1F0 - 1F7). Closed Secondary HD I/O ports (170 - 177). J13 1-2 HD IRQ 15 (when secondary I/O ports selected via J12). 2-3 (Default) HD IRQ 14 (when primary I/O ports selected via J12). } *