旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴커 � Hard Disk Tech Specs(tm) v3.0 � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴켸 Hard Drive Solutions Family(tm)  //TMC-7000FASST2 01 D88, 82, 95, 82 D95, 82, 95, 60 D95, 60, 88, 60 D88, 60, 88, 82 T95, 72, 0, 1, J1 C83, 80, 1, 1 T82, 83, 0, 1, J2 C40, 92, 1, 0 T45, 91, 0, 1, J3 T5, 91, 0, 1, J4 T82, 83, 0, 4, Term Term T12, 75, 0, 4, Spare Fuse T85, 92, 0, 1, F1 T45, 60, 0, 1, W2 T63, 60, 0, 1, W3 W1 W4 T78, 73, 0, 1, W5 T61, 79, 0, 1, W6 W9 T77, 61, 0, 1, W98 T26, 81, 0, 1, W200 W201 { Drives: 7 SCSI devices supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 External SCSI connector. J2 Internal SCSI connector. J3 Floppy connector. J4 LED connector. F1 Fuse (a spare is located on board). W1 -1 Closed Floppy IRQ 3. -2 Closed Floppy IRQ 4. -3 Closed Floppy IRQ 5. -4 Closed Floppy IRQ 7. -5 Closed Floppy IRQ 9. W2 -1 Open DMA channel 5. -2 Open -3 Closed -4 Open -5 Open -6 Closed Open (Default) DMA channel 6. Closed Open Open Closed Open Closed DMA channel 7. Open Open Closed Open Open -7 Closed HD IRQ 10. -8 Closed HD IRQ 11. -9 Closed HD IRQ 12. -10 Closed HD IEQ 14. -11 Closed (Default) HD IRQ 15. W3 12345 (X - installed). ||||| (o - not installed). oXXXX I/O port 308. XoXXX I/O port 310. ooXXX I/O port 318. XXoXX I/O port 320. oXoXX I/O port 328. XooXX I/O port 330. oooXX I/O port 338. XXXoX I/O port 340. oXXoX I/O port 348. XoXoX (Default) I/O port 350. ooXoX I/O port 358. XXooX I/O port 360. oXooX I/O port 368. XoooX I/O port 370. ooooX I/O port 378. XXXXo I/O port 380. oXXXo I/O port 388. XoXXo I/O port 390. ooXXo I/O port 398. XXoXo I/O port 3A0. oXoXo I/O port 3A8. XooXo I/O port 3B0. oooXo I/O port 3B8. XXXoo I/O port 3C0. oXXoo I/O port 3C8. XoXoo I/O port 3D0. ooXoo I/O port 3D8. XXooo I/O port 3E0. oXooo I/O port 3E8. Xoooo I/O port 3F0. W4 1234 (X - installed). |||| (o - not installed). XXoX BIOS address C:8000. oXoX BIOS address C:A000. XooX BIOS address C:C000. oooX (Default) BIOS address C:E000. XXXo BIOS address D:0000. oXXo BIOS address D:2000. XoXo BIOS address D:4000. ooXo BIOS address D:6000. XXoo BIOS address D:8000. oXoo BIOS address D:A000. Xooo BIOS address D:C000. W5 Open Termination power disabled. Closed Termination power enabled. W6 Closed No floppy cable connected. W9 Closed Open Floppy cable present. Open W98 Open BIOS disabled. Closed BIOS enabled (you MUST install this jumper unless this board is the second TMC-7000FASST2 in the system). W200 1-2 1st floppy is standard AT-type. 2-3 1st floppy is high-speed PS/2-type. W201 1-2 2nd floppy is standard AT-type. 2-3 2nd floppy is high-speed PS/2-type. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-7000EX 03 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C60, 91, 1, 0 T65, 89, 0, 1, J2 T75, 66, 0, 1, LED T75, 60, 0, 1, W4 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. LED Terminator LED (when on, this LED indicates proper termination). W4 Open Termination power disabled. Closed Termination power enabled. Note: This EISA adapter supports 32-bit, 1st-party Bus Master data xfers. All configuration is accomplished via software. The exception to this is terminator power (see W4). } * //MCS-350 32 C80, 85, 1, 1 T80, 88, 0, 1, J1 T75, 66, 0, 1, W1 { Drives: 7 SCSI devices supported. J1 Internal SCSI connector. W4 Open Termination power disabled. Closed Termination power enabled. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. Note: All other settings are configured via the PS/2 reference disk. } * //MCS-700 32 D88, 84, 95, 84 D95, 84, 95, 64 D95, 64, 88, 64 D88, 64, 88, 84 T95, 74, 0, 1, J1 C67, 91, 1, 0 T73, 89, 0, 1, J2 T30, 80, 0, 1, J3 T50, 88, 0, 1, F1 W1 T66, 85, 0, 1, Term. Term. { Drives: 7 SCSI devices supported. J1 External SCSI connector (SCSI-2 compatible). J2 Internal SCSI connector (SCSI-1 compatible). J3 DC power connector. F1 Thermal fuse. W1 Open Termination power disabled. Closed Termination power enabled. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. Note: All other settings are configured via the PS/2 reference disk. } * //TMC-830 10 D62, 82, 75, 82 D75, 82, 75, 60 D75, 60, 62, 60 D62, 60, 62, 82 T75, 72, 0, 1, J1 C55, 80, 1, 1 T54, 83, 0, 1, J2 T55, 94, 0, 1, Terminator T55, 91, 0, 1, Terminator T55, 88, 0, 1, Terminator T25, 91, 0, 1, W1 W2 T36, 55, 0, 1, W3 W4 T50, 55, 0, 1, W5 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open Open BIOS address C:8000 - C:9FFF. Closed Closed BIOS address C:E000 - C:FFFF. Open Closed BIOS address D:E000 - D:FFFF. Closed W3 Open (Default) IRQ 5. W4 Closed Closed IRQ 3. Open W5 Open (Default) Zero wait state disabled. Closed Zero wait state enabled. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-840 10 D62, 82, 75, 82 D75, 82, 75, 60 D75, 60, 62, 60 D62, 60, 62, 82 T75, 72, 0, 1, J1 C35, 93, 1, 0 T40, 91, 0, 1, J2 T25, 85, 0, 1, Terminator Terminator Terminator T46, 62, 0, 1, W1 W2 T36, 55, 0, 1, W3 W4 T22, 59, 0, 1, W6 T22, 56, 0, 1, W7 T21, 91, 0, 1, J3 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. J3 LED connector. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open Open BIOS address C:8000 - C:9FFF. Closed Closed BIOS address C:E000 - C:FFFF. Open Closed BIOS address D:E000 - D:FFFF. Closed W3 Open (Default) IRQ 5. W4 Closed Closed IRQ 3. Open W6 Closed (Default) Short time-out delay. W7 Open Open Long time-out delay. Closed Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-845 10 D62, 82, 75, 82 D75, 82, 75, 60 D75, 60, 62, 60 D62, 60, 62, 82 T75, 72, 0, 1, J1 C35, 93, 1, 0 T40, 91, 0, 1, J2 T21, 91, 0, 1, J3 T25, 85, 0, 1, Terminator Terminator Terminator T46, 66, 0, 1, W1 W2 T36, 55, 0, 1, W3 W4 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. J3 LED connector. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open Open BIOS address C:8000 - C:9FFF. Closed Closed BIOS address C:E000 - C:FFFF. Open Closed BIOS address D:E000 - D:FFFF. Closed W3 Open (Default) IRQ 5. W4 Closed Closed IRQ 3. Open Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-850M 20 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C59, 93, 1, 0 T64, 91, 0, 1, J2 T54, 85, 0, 1, Terminator Terminator T21, 91, 0, 1, F1 T63, 62, 0, 1, W1 W2 W3 W5 T17, 88, 0, 1, W4 T56, 66, 0, 1, W6 W7 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. F1 Thermal fuse. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open W3 1-2 Closed 3-4 Closed Open BIOS address C:8000 - C:9FFF. Closed 1-2 Closed 3-4 Closed Closed BIOS address C:E000 - C:FFFF. Open 1-2 Closed 3-4 Closed Closed BIOS address D:E000 - D:FFFF. Closed 1-2 Closed 3-4 Closed Open Extended BIOS address E:8000 - E:9FFF. Open 1-3 Closed 2-4 Closed Closed Extended BIOS address E:C000 - E:FFFF. Open 1-3 Closed 2-4 Closed W4 Open Termination power disabled. Closed Termination power enabled. W5 Open (Default) Zero wait state disabled. Closed Zero wait state enabled. W6 1-2 Closed (Default) IRQ 3. W7 2-3 Closed IRQ 5. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-860 21 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C60, 93, 1, 0 T65, 91, 0, 1, J2 T15, 86, 0, 1, J3 T57, 85, 0, 1, Term. Term. Term. T69, 62, 0, 1, W1 W2 T46, 55, 0, 1, W4 T75, 55, 0, 1, W5 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. J3 LED connector. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open Open BIOS address C:8000 - C:9FFF. Closed Closed BIOS address C:E000 - C:FFFF. Open Closed BIOS address D:E000 - D:FFFF. Closed W4 -1 IRQ 3. -2 IRQ 4. -3 (Default) IRQ 5. -4 IRQ 10. -5 IRQ 11. -6 IRQ 12. -7 IRQ 14. -8 IRQ 15. W5 Open (Default) Zero wait state disabled. Closed Zero wait state enabled. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-860M 21 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C59, 93, 1, 0 T64, 91, 0, 1, J2 T16, 82, 0, 1, J8 T54, 85, 0, 1, Terminator Terminator T44, 86, 0, 1, F1 T63, 62, 0, 1, W1 W2 W3 W5 T44, 91, 0, 1, W4 T69, 55, 0, 1, W7 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. J8 LED connector. F1 Thermal fuse. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open W3 1-2 Closed 3-4 Closed Open BIOS address C:8000 - C:9FFF. Closed 1-2 Closed 3-4 Closed Closed BIOS address C:E000 - C:FFFF. Open 1-2 Closed 3-4 Closed Closed BIOS address D:E000 - D:FFFF. Closed 1-2 Closed 3-4 Closed Open Extended BIOS address E:8000 - E:9FFF. Open 1-3 Closed 2-4 Closed Closed Extended BIOS address E:C000 - E:FFFF. Open 1-3 Closed 2-4 Closed W4 Open Termination power disabled. Closed Termination power enabled. W5 Open (Default) Zero wait state disabled. Closed Zero wait state enabled. W7 1-2 Closed (Default) IRQ 3. 3-4 Closed IRQ 4. 5-6 Closed IRQ 5. 7-8 Closed IRQ 10. 9-10 Closed IRQ 11. 11-12 Closed IRQ 12. 13-14 Closed IRQ 14. 15-16 Closed IRQ 15. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-870 00 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C75, 80, 1, 1 T74, 83, 0, 1, J2 C47, 88, 1, 1 T46, 92, 0, 1, J3 C40, 88, 1, 1 T39, 92, 0, 1, J4 T5, 85, 0, 1, J5 T22, 55, 0, 1, E1 E2 T56, 83, 0, 2, E3 E4 T58, 83, 0, 2, E5 E6 T70, 55, 0, 1, E7 E8 T62, 88, 0, 1, DIP SWITCH { Drives: 7 SCSI devices supported. 4 floppy drives (360KB, 720KB, 1.2MB, or 1.44MB). Note: The first two floppies are controlled directly by the host computer's BIOS, so support for various drive capacities depends upon the capabilities of your system. Also, you must obtain and install a special driver in order to access the last two floppy drives (the capacities of which are determined by that particular device driver). J1 External SCSI connector. J2 Internal SCSI connector. J3 Primary floppy connector. J4 Secondary floppy connector. J5 LED connector. E1-E2 Open (Default) Primary I/O ports. Closed Secondary I/O port. E3-E4 Open (Default) BIOS address C:A000 - C:BFFF. E5-E6 Open Open BIOS address C:8000 - C:9FFF. Closed Closed BIOS address C:E000 - C:FFFF. Open Closed BIOS address D:E000 - D:FFFF. Closed E7-E8 Open (Default) Zero wait state disabled. Closed Zero wait state enabled. Note: The following settings for the 8-position dip switch apply only to v4.1E of the controller's BIOS. For v6.0x, all switches should be in the 'OFF' position. S1 Off Floppy drive 0 is 360KB. On Floppy drive 0 is 1.2MB. S2 Off Floppy drive 1 is 360KB. On Floppy drive 1 is 1.2MB. S3 Off Floppy drives 2 & 3 are 360KB (both drives must be the same type). On Floppy drives 2 & 3 are 1.2MB (both drives must be the same type). S4 Off No SCSI devices attached. On (Default) 1 or more SCSI devices attached. S5 Off Auto-detect number of floppy drives. S6 Off S7 Off On 1 floppy installed. Off Off Off 2 floppies installed. On Off On 3 floppies installed. On Off Off 4 floppies installed. Off On } * //TMC-875 00 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C60, 93, 1, 0 T65, 91, 0, 1, J2 C30, 93, 1, 0 T35, 91, 0, 1, J3 C10, 93, 1, 0 T15, 91, 0, 1, J4 T5, 86, 0, 1, J5 T57, 85, 0, 1, Term. Term. Term. T37, 75, 0, 1, F1 F2 T69, 62, 0, 1, W1 W2 T42, 55, 0, 1, W3 W4 { Drives: 7 SCSI devices supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 External SCSI connector. J2 Internal SCSI connector. J3 Primary floppy connector. J4 Secondary floppy connector. J5 LED connector. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open Open BIOS address C:8000 - C:9FFF. Closed Closed BIOS address C:E000 - C:FFFF. Open Closed BIOS address D:E000 - D:FFFF. Closed W3 Closed (Default) IRQ 3. W4 Open Open IRQ 5. Closed F1 Open (Default) Floppy I/O ports 3F2, 3F4, 3F5, 3F7. Floppy DMA channel 2, IRQ 6. Closed (Default) Floppy I/O ports 372, 374, 375, 377. Floppy DMA channel 3, IRQ 5. F2 Open (Default) No AT hard disk present. Closed AT hard disk present. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-880 01 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C55, 93, 1, 0 T60, 91, 0, 1, J2 C40, 87, 1, 1 T39, 91, 0, 1, J3 T5, 91, 0, 1, J4 T45, 85, 0, 1, Terminator Terminator Terminator T22, 86, 0, 1, F1 F2 T71, 62, 0, 1, W1 W2 T46, 55, 0, 1, W4 T55, 61, 0, 1, W6 W7 { Drives: 7 SCSI devices supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 External SCSI connector. J2 Internal SCSI connector. J3 Floppy connector. J4 LED connector. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open Open BIOS address C:8000 - C:9FFF. Closed Closed BIOS address C:E000 - C:FFFF. Open Closed BIOS address D:E000 - D:FFFF. Closed W4 -1 IRQ 3. -2 IRQ 4. -3 (Default) IRQ 5. -4 IRQ 10. -5 IRQ 11. -6 IRQ 12. -7 IRQ 14. -8 IRQ 15. W6 Closed (Default) Short time-out delay. W7 Open Open Long time-out delay. Closed F1 Open (Default) Floppy I/O ports 3F2, 3F4, 3F5, 3F7. Floppy DMA channel 2, IRQ 6. Closed (Default) Floppy I/O ports 372, 374, 375, 377. Floppy DMA channel 3, IRQ 5. F2 Open (Default) No AT hard disk present. Closed AT hard disk present. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-885 01 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C60, 93, 1, 0 T65, 91, 0, 1, J2 C30, 93, 1, 0 T35, 91, 0, 1, J3 C10, 93, 1, 0 T15, 91, 0, 1, J4 T5, 86, 0, 1, J5 T57, 85, 0, 1, Term. Term. Term. T43, 65, 0, 1, F1 F2 T69, 62, 0, 1, W1 W2 T46, 55, 0, 1, W4 T75, 55, 0, 1, W5 { Drives: 7 SCSI devices supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 External SCSI connector. J2 Internal SCSI connector. J3 Primary floppy connector. J4 Secondary floppy connector. J5 LED connector. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open Open BIOS address C:8000 - C:9FFF. Closed Closed BIOS address C:E000 - C:FFFF. Open Closed BIOS address D:E000 - D:FFFF. Closed W4 -1 IRQ 3. -2 IRQ 4. -3 (Default) IRQ 5. -4 IRQ 10. -5 IRQ 11. -6 IRQ 12. -7 IRQ 14. -8 IRQ 15. W5 Open (Default) Zero wait state disabled. Closed Zero wait state enabled. F1 Open (Default) Floppy I/O ports 3F2, 3F4, 3F5, 3F7. Floppy DMA channel 2, IRQ 6. Closed (Default) Floppy I/O ports 372, 374, 375, 377. Floppy DMA channel 3, IRQ 5. F2 Open (Default) No AT hard disk present. Closed AT hard disk present. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-885M 21 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C59, 93, 1, 0 T64, 91, 0, 1, J2 C19, 93, 1, 0 T24, 91, 0, 1, J3 T16, 82, 0, 1, J8 T54, 85, 0, 1, Terminator Terminator T44, 86, 0, 1, F1 T63, 62, 0, 1, W1 W2 W3 W5 T44, 91, 0, 1, W4 T56, 72, 0, 1, W6 T69, 55, 0, 1, W7 { Drives: 7 SCSI devices supported. 2 floppy drives (360KB, 720KB, 1.2MB, or 1.44MB). J1 External SCSI connector. J2 Internal SCSI connector. J3 Floppy connector. J8 LED connector. F1 Thermal fuse. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open W3 1-2 Closed 3-4 Closed Open BIOS address C:8000 - C:9FFF. Closed 1-2 Closed 3-4 Closed Closed BIOS address C:E000 - C:FFFF. Open 1-2 Closed 3-4 Closed Closed BIOS address D:E000 - D:FFFF. Closed 1-2 Closed 3-4 Closed Open Extended BIOS address E:8000 - E:9FFF. Open 1-3 Closed 2-4 Closed Closed Extended BIOS address E:C000 - E:FFFF. Open 1-3 Closed 2-4 Closed W4 Open Termination power disabled. Closed Termination power enabled. W5 Open (Default) Zero wait state disabled. Closed Zero wait state enabled. W6 1-2 Closed (Default) Floppy controller enabled. 3-4 Closed 5-6 Closed 1-2 Open Floppy controller disabled. 3-4 Open 5-6 Open W7 1-2 Closed (Default) IRQ 3. 3-4 Closed IRQ 4. 5-6 Closed IRQ 5. 7-8 Closed IRQ 10. 9-10 Closed IRQ 11. 11-12 Closed IRQ 12. 13-14 Closed IRQ 14. 15-16 Closed IRQ 15. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-850M 20 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C59, 93, 1, 0 T64, 91, 0, 1, J2 T54, 85, 0, 1, Terminator Terminator T21, 91, 0, 1, F1 T63, 62, 0, 1, W1 W2 W3 W5 T17, 88, 0, 1, W4 T56, 66, 0, 1, W6 W7 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. F1 Thermal fuse. W1 Open (Default) BIOS address C:A000 - C:BFFF. W2 Open W3 1-2 Closed 3-4 Closed Open BIOS address C:8000 - C:9FFF. Closed 1-2 Closed 3-4 Closed Closed BIOS address C:E000 - C:FFFF. Open 1-2 Closed 3-4 Closed Closed BIOS address D:E000 - D:FFFF. Closed 1-2 Closed 3-4 Closed Open Extended BIOS address E:8000 - E:9FFF. Open 1-3 Closed 2-4 Closed Closed Extended BIOS address E:C000 - E:FFFF. Open 1-3 Closed 2-4 Closed W4 Open Termination power disabled. Closed Termination power enabled. W5 Open (Default) Zero wait state disabled. Closed Zero wait state enabled. W6 1-2 Closed (Default) IRQ 3. W7 2-3 Closed IRQ 5. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-1650 21 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C61, 93, 1, 0 T66, 91, 0, 1, J2 T16, 76, 0, 1, J3 T55, 85, 0, 1, Terminator Terminator T50, 84, 0, 1, F1 T46, 81, 0, 1, W4 T73, 55, 0, 1, W1 T60, 66, 0, 1, W2 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. J3 LED connector. F1 Thermal fuse. W1 -1 Open IRQ 3. -2 Open -3 Open -1 Closed (Default) IRQ 5. -2 Open -3 Open -1 Open IRQ 10. -2 Closed -3 Open -1 Closed IRQ 11. -2 Closed -3 Open -1 Open IRQ 12. -2 Open -3 Closed -1 Closed IRQ 14. -2 Open -3 Closed -1 Open IRQ 15. -2 Closed -3 Closed W1 -4 Open I/O ports 140 - 14F. -5 Open Closed I/O ports 150 - 15F. Open Open I/O ports 160 - 16F. Closed Closed (Default) I/O ports 170 - 17F. Closed W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF. -7 Open Open BIOS address C:8000 - C:9FFF. Open Open BIOS address C:E000 - C:FFFF. Closed Closed BIOS address D:E000 - D:FFFF. Closed W2 -1 Closed (Default) BIOS enabled. -2 Closed Open BIOS disabled. Open W4 Open Termination power disabled. Closed Termination power enabled. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-1660-solder 21 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C61, 93, 1, 0 T66, 91, 0, 1, J2 T16, 78, 0, 1, J3 T58, 85, 0, 1, Term. W3 Term. T38, 91, 0, 1, F1 T46, 91, 0, 1, W4 T73, 55, 0, 1, W1 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. J3 LED connector. F1 Thermal fuse. W1 -1 Open IRQ 3. -2 Open -3 Open -1 Closed (Default) IRQ 5. -2 Open -3 Open -1 Open IRQ 10. -2 Closed -3 Open -1 Closed IRQ 11. -2 Closed -3 Open -1 Open IRQ 12. -2 Open -3 Closed -1 Closed IRQ 14. -2 Open -3 Closed -1 Open IRQ 15. -2 Closed -3 Closed W1 -4 Open (Default) I/O ports 140 - 14F. -5 Open Closed I/O ports 150 - 15F. Open Open I/O ports 160 - 16F. Closed Closed I/O ports 170 - 17F. Closed W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF. -7 Open Open BIOS address C:8000 - C:9FFF. Open Open BIOS address C:E000 - C:FFFF. Closed Closed BIOS address D:E000 - D:FFFF. Closed W3 All Reserved. W4 Open Termination power disabled. Closed Termination power enabled. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-1660-surface 21 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C61, 93, 1, 0 T66, 91, 0, 1, J2 T16, 78, 0, 1, J3 T16, 55, 0, 1, J4 T57, 85, 0, 1, Terminator Terminator T44, 91, 0, 1, F1 T48, 86, 0, 1, W4 T73, 55, 0, 1, W1 T52, 60, 0, 1, W2 { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. J3 LED connector. J4 DC power connector. F1 Thermal fuse. W1 -1 Open IRQ 3. -2 Open -3 Open -1 Closed (Default) IRQ 5. -2 Open -3 Open -1 Open IRQ 10. -2 Closed -3 Open -1 Closed IRQ 11. -2 Closed -3 Open -1 Open IRQ 12. -2 Open -3 Closed -1 Closed IRQ 14. -2 Open -3 Closed -1 Open IRQ 15. -2 Closed -3 Closed W1 -4 Open (Default) I/O ports 140 - 14F. -5 Open Closed I/O ports 150 - 15F. Open Open I/O ports 160 - 16F. Closed Closed I/O ports 170 - 17F. Closed W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF. -7 Open Open BIOS address C:8000 - C:9FFF. Open Open BIOS address C:E000 - C:FFFF. Closed Closed BIOS address D:E000 - D:FFFF. Closed W2 -1 Reserved. -2 Reserved. -3 Reserved. -4 Closed (Default) BIOS ROM enabled. Open BIOS ROM disabled. -5 Closed (Default) ROM and RAM enabled. Open ROM and RAM disabled. W4 Open Termination power disabled. Closed Termination power enabled. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-1670 21 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C61, 93, 1, 0 T66, 91, 0, 1, J2 T16, 76, 0, 1, J3 C21, 93, 1, 0 T26, 91, 0, 1, J5 T55, 85, 0, 1, Terminator Terminator T48, 84, 0, 1, F1 T44, 81, 0, 1, W4 T73, 55, 0, 1, W1 T58, 66, 0, 1, W3 W2 { Drives: 7 SCSI devices supported. 2 floppy drives (360KB, 720KB, 1.2MB, or 1.44MB). J1 External SCSI connector. J2 Internal SCSI connector. J3 LED connector. J5 Floppy connector. F1 Thermal fuse. W1 -1 Open IRQ 3. -2 Open -3 Open -1 Closed (Default) IRQ 5. -2 Open -3 Open -1 Open IRQ 10. -2 Closed -3 Open -1 Closed IRQ 11. -2 Closed -3 Open -1 Open IRQ 12. -2 Open -3 Closed -1 Closed IRQ 14. -2 Open -3 Closed -1 Open IRQ 15. -2 Closed -3 Closed W1 -4 Open I/O ports 140 - 14F. -5 Open Closed I/O ports 150 - 15F. Open Open I/O ports 160 - 16F. Closed Closed (Default) I/O ports 170 - 17F. Closed W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF. -7 Open Open BIOS address C:8000 - C:9FFF. Open Open BIOS address C:E000 - C:FFFF. Closed Closed BIOS address D:E000 - D:FFFF. Closed W2 -1 Closed (Default) BIOS enabled. -2 Closed Open BIOS disabled. Open W3 -1 Closed (Default) Floppy controller enabled. -2 Closed -3 Closed Open Floppy controller disabled. Open Open W4 Open Termination power disabled. Closed Termination power enabled. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-1680-solder 01 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C61, 93, 1, 0 T66, 91, 0, 1, J2 T6, 78, 0, 1, J3 C28, 93, 1, 0 T33, 91, 0, 1, J5 C8, 93, 1, 0 T13, 91, 0, 1, J6 T58, 85, 0, 1, Term. W3 Term. T47, 91, 0, 1, F1 W4 T73, 55, 0, 1, W1 T64, 60, 0, 1, W2 { Drives: 7 SCSI devices supported. 4 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 External SCSI connector. J2 Internal SCSI connector. J3 LED connector. J5 Primary floppy connector. J6 Secondary floppy connector. F1 Thermal fuse. W1 -1 Open IRQ 3. -2 Open -3 Open -1 Closed (Default) IRQ 5. -2 Open -3 Open -1 Open IRQ 10. -2 Closed -3 Open -1 Closed IRQ 11. -2 Closed -3 Open -1 Open IRQ 12. -2 Open -3 Closed -1 Closed IRQ 14. -2 Open -3 Closed -1 Open IRQ 15. -2 Closed -3 Closed W1 -4 Open (Default) I/O ports 140 - 14F. -5 Open Closed I/O ports 150 - 15F. Open Open I/O ports 160 - 16F. Closed Closed I/O ports 170 - 17F. Closed W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF. -7 Open Open BIOS address C:8000 - C:9FFF. Open Open BIOS address C:E000 - C:FFFF. Closed Closed BIOS address D:E000 - D:FFFF. Closed W2 -1 Closed (Default) Primary floppy enabled. Open Primary floppy disabled. -2 Closed Secondary floppy enabled. Open (Default) Secondary floppy disabled. -3 Closed HD controller disabled. Open (Default) HD controller enabled. -4 Reserved. -5 Reserved. W3 All Reserved. W4 Open Termination power disabled. Closed Termination power enabled. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //TMC-1680-surface 01 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J1 C61, 93, 1, 0 T66, 91, 0, 1, J2 T6, 78, 0, 1, J3 T6, 55, 0, 1, J4 C12, 93, 1, 0 T17, 91, 0, 1, J5 C12, 85, 1, 0 T17, 84, 0, 1, J6 T56, 85, 0, 1, Terminator Terminator T47, 86, 0, 1, W4 T73, 55, 0, 1, W1 T55, 60, 0, 1, W2 { Drives: 7 SCSI devices supported. 4 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 External SCSI connector. J2 Internal SCSI connector. J3 LED connector. J5 Primary floppy connector. J6 Secondary floppy connector. W1 -1 Open IRQ 3. -2 Open -3 Open -1 Closed (Default) IRQ 5. -2 Open -3 Open -1 Open IRQ 10. -2 Closed -3 Open -1 Closed IRQ 11. -2 Closed -3 Open -1 Open IRQ 12. -2 Open -3 Closed -1 Closed IRQ 14. -2 Open -3 Closed -1 Open IRQ 15. -2 Closed -3 Closed W1 -4 Open (Default) I/O ports 140 - 14F. -5 Open Closed I/O ports 150 - 15F. Open Open I/O ports 160 - 16F. Closed Closed I/O ports 170 - 17F. Closed W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF. -7 Open Open BIOS address C:8000 - C:9FFF. Open Open BIOS address C:E000 - C:FFFF. Closed Closed BIOS address D:E000 - D:FFFF. Closed W2 -1 Closed (Default) Primary floppy enabled. Open Primary floppy disabled. -2 Closed Secondary floppy enabled. Open (Default) Secondary floppy disabled. -3 Closed HD controller disabled. Open (Default) HD controller enabled. -4 Closed (Default) BIOS ROM enabled. Open BIOS ROM disabled. -5 Closed (Default) ROM and RAM enabled. Open ROM and RAM disabled. W4 Open Termination power disabled. Closed Termination power enabled. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } *