旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴커 � Hard Disk Tech Specs(tm) v3.0 � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴켸 Hard Drive Solutions Family(tm)  //EV-8110 01 D86, 82, 95, 82 D95, 82, 95, 60 D95, 60, 86, 60 D86, 60, 86, 82 T95, 72, 0, 1, C1 C70, 93, 1, 0 T75, 91, 0, 1, C2 C15, 93, 1, 0 T20, 91, 0, 1, C3 T8, 91, 0, 1, C4 T34, 91, 0, 1, J1 J3 J4 T72, 86, 0, 1, J5 T78, 58, 0, 1, J6 T60, 91, 0, 1, J8 J7 { Drives: 7 SCSI devices supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). C1 External SCSI connector. C2 Internal SCSI connector. C3 Floppy connector. C4 LED connector. J1 Closed (Default) Floppy controller enabled. Open Floppy controller disabled. J3 Open (Default) Precomp = 125ns. Closed Precomp = 187ns. J4 Open (Default) Single-speed floppies installed. Closed Dual-speed floppies installed. J5 ooo BIOS address C:4000 - C:7FFF. ooo ooX BIOS address C:8000 - C:BFFF. ooX oXo BIOS address C:C000 - C:FFFF. oXo oXX BIOS address D:0000 - D:3FFF. oXX Xoo BIOS address D:4000 - D:7FFF. Xoo XoX BIOS address D:8000 - D:BFFF. XoX XXo (Default) BIOS address D:C000 - D:FFFF. XXo J6 Open Logic ground (MUST remain open). J7 Closed Termination power enabled. Open (Default) Termination power disabled. J8 1-2 Closed External and internal power source for on board terminators. 2-3 Closed (Default) Internal power source for on board terminators. Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //EV-8116 01 C25, 93, 1, 0 T30, 91, 0, 1, J1 C64, 93, 1, 0 T69, 91, 0, 1, J2 D82, 82, 95, 82 D95, 82, 95, 60 D95, 60, 82, 60 D82, 60, 82, 82 T95, 72, 0, 1, J3 T66, 80, 0, 1, Term. Term. T20, 91, 0, 1, W1 T42, 91, 0, 1, W2 W3 W4 W5 W6 T85, 93, 0, 4, W7 T88, 93, 0, 4, W8 T81, 58, 0, 1, W9 T78, 85, 0, 1, F1 { Drives: 7 SCSI devices supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 Floppy connector. J2 Internal SCSI connector. J3 External SCSI connector. F1 Fuse. W1 Open Floppy controller disabled. Closed (Default) Floppy controller enabled. W2 -1 Open Floppy IRQ 10. -2 Closed Closed (Default) Floppy IRQ 6. Open -3 Closed (Default) Floppy DMA channel 2. -4 Open -5 Closed -6 Open -3 Open Floppy DMA channel 3. -4 Closed -5 Open -6 Closed W3 1-6 Open BIOS address C:4000 - C:BFFF. 2-5 Open 3-4 Open Open BIOS address C:8000 - C:BFFF. Open Closed Open BIOS address C:C000 - C:FFFF. Closed Open Open BIOS address D:0000 - D:3FFF. Closed Closed Closed BIOS address D:4000 - D:7FFF. Open Open Closed BIOS address D:8000 - D:BFFF. Open Closed Closed (Default) BIOS address D:C000 - D:FFFF. Closed Open W4 1-2 Open Factory use. 2-3 Closed Factory use. Leave closed. W5 1-2 Closed Factory use. Leave closed. 2-3 Open Factory use. W6 Open (Default) Primary floppy I/O ports (3F0 - 3FF). Closed Secondary floppy I/O ports (370 - 37F). W7 1-2 Closed External and internal power source for on board terminators. 2-3 Closed (Default) Internal power source for on board terminators. W8 Closed (Default) Termination power enabled. Open Termination power disabled. W9 Open Logic ground (MUST remain open). Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //EV-8119 00 D86, 82, 95, 82 D95, 82, 95, 60 D95, 60, 86, 60 D86, 60, 86, 82 T95, 72, 0, 1, J1 C80, 80, 1, 1 T79, 84, 0, 1, J2 T70, 65, 0, 1, Term. T70, 61, 0, 1, Term. T58, 92, 0, 1, W1 T65, 95, 0, 4, W2 T77, 95, 0, 4, W3 T81, 95, 0, 4, W4 T84, 95, 0, 4, W5 T87, 95, 0, 4, Fuse { Drives: 7 SCSI devices supported. J1 External SCSI connector. J2 Internal SCSI connector. Fuse Thermal fuse. W1 ooo BIOS address C:4000 - C:7FFF. ooo ooX BIOS address C:8000 - C:BFFF. ooX oXo BIOS address C:C000 - C:FFFF. oXo oXX BIOS address D:0000 - D:3FFF. oXX Xoo BIOS address D:4000 - D:7FFF. Xoo XoX BIOS address D:8000 - D:BFFF. XoX XXo (Default) BIOS address D:C000 - D:FFFF. XXo W2 1-2 U7 contains RAM. 2-3 (Default) U7 contains an EPROM. W3 1-2 External and internal power source for on board terminators. 2-3 (Default) Internal power source for on board terminators. W4 Closed (Default) Termination power enabled. Open Termination power disabled. W5 Open Logic ground (MUST remain open). Terminators: Default is installed. If this is not the 1st or last in a series of SCSI devices, or if in-line terminators are in use, remove all terminating resistor packs. } * //EV-8120 21 C70, 92, 1, 0 T75, 90, 0, 1, C1 C18, 92, 1, 0 T23, 90, 0, 1, C2 T15, 80, 0, 1, C9 T42, 92, 0, 4, J1 T42, 90, 0, 1, J2 J3 T53, 92, 0, 4, J4 T56, 92, 0, 4, J5 T59, 92, 0, 4, J6 T62, 92, 0, 4, J7 T65, 92, 0, 4, J8 T68, 92, 0, 4, J10 { Drives: 2 IDE (AT) drives supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). C1 Floppy connector. C2 IDE interface connector. C9 LED connector. J1 Open (Default) I/O CHRDY connectoed to AT bus. Closed I/O CHRDY not connected to AT bus. J2 All open (Default) DMA REQ disabled. 1-6 DMA REQ 5. 2-5 DMA REQ 6. 3-4 DMA REQ 7. J3 All open (Default) DMA ACK disabled. 1-6 DMA ACK 5. 2-5 DMA ACK 6. 3-4 DMA ACK 7. J4 Open (Default) DMA ACK connected to AT bus. Closed DMA ACK not connected to AT bus. J5 Open (Default) Primary HD I/O ports (1F0 - 1F7) and primary floppy I/O ports (3F0 - 3F7). Closed Secondary HD I/O ports (170 - 177) and secondary floppy I/O ports (370 - 377). J6 1-2 Host system has a Phoenix BIOS. 2-3 (Default) Host system has IBM, Award, AMI, or other BIOS. J7 Open Do not change this jumper. J8 Open Floppy controller disabled. Closed (Default) Floppy controller enabled. J10 Open Zero wait state. Closed (Default) Back-to-back I/O delay (necessary for 25 - 30 MHz systems with a fast bus - has no effect on slower systems). } * //EV-8120A 21 C70, 92, 1, 0 T75, 90, 0, 1, C1 C18, 92, 1, 0 T23, 90, 0, 1, C2 C70, 85, 1, 0 T75, 83, 0, 1, C3 T15, 80, 0, 1, C9 T42, 92, 0, 4, J1 T42, 90, 0, 1, J2 J3 T53, 92, 0, 4, J4 T56, 92, 0, 4, J5 T59, 92, 0, 4, J6 T62, 92, 0, 4, J7 T65, 92, 0, 4, J8 T68, 92, 0, 4, J10 T68, 85, 0, 4, J11 T65, 85, 0, 4, J12 T62, 85, 0, 4, J13 { Drives: 2 IDE (AT) drives supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). C1 Primary connector. C2 IDE interface connector. C3 Secondary floppy connector. C9 LED connector. J1 Closed (Default) I/O CHRDY connectoed to AT bus. Open I/O CHRDY not connected to AT bus. J2 All open (Default) DMA REQ disabled. 1-6 DMA REQ 5. 2-5 DMA REQ 6. 3-4 DMA REQ 7. J3 All open (Default) DMA ACK disabled. 1-6 DMA ACK 5. 2-5 DMA ACK 6. 3-4 DMA ACK 7. J4 Closed (Default) DMA ACK connected to AT bus. Open DMA ACK not connected to AT bus. J5 Open Enable ATA hard disk mode. Closed Enable ATA tape drive mode. J6 1-2 Host system has a Phoenix BIOS. 2-3 (Default) Host system has IBM, Award, AMI, or other BIOS. J7 Open Do not change this jumper. J8 Open Floppy controller disabled. Closed (Default) Floppy controller enabled. J10 Open Zero wait state. Closed (Default) Back-to-back I/O delay (necessary for 25 - 30 MHz systems with a fast bus - has no effect on slower systems). J11 Open (Default) Primary floppy I/O ports (3F0 - 3F7). Closed Secondary floppy I/O ports (370 - 377). J12 Open (Default) Primary HD I/O ports (1F0 - 1F7). Closed Secondary HD I/O ports (170 - 177). J13 1-2 HD IRQ 15 (when secondary I/O ports selected via J12). 2-3 (Default) HD IRQ 14 (when primary I/O ports selected via J12). } * //EV-341 01 C71, 92, 1, 0 T76, 90, 0, 1, J1 C59, 92, 0, 0 T62, 90, 0, 1, J2 C59, 86, 0, 0 T62, 84, 0, 1, J3 C40, 92, 1, 0 T45, 90, 0, 1, J4 T5, 90, 0, 1, J5 T45, 55, 0, 1, W3 W1 T32, 78, 0, 1, W2 T18, 55, 0, 1, W4 { Drives: 2 ESDI drives supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 HD control connector. J2 Drive 0 data connector. J3 Drive 1 data connector. J4 Floppy connector. J5 LED connector. W1 1-2 (Default) Floppy DMA ACK 2 enabled. 2-3 Floppy DMA ACK 2 disabled (when disabling floppy controller). W2 1-2 (Default) Normal DOS mode. 2-3 Disable floppy controller under OS/2. W3 Closed (Default) Floppy controller enabled. Open Floppy controller disabled (see also W1). W4 1-2 (Default) Do not change. } * //EV-346M 01 C50, 92, 1, 0 T55, 90, 0, 1, J1 C37, 92, 0, 0 T40, 90, 0, 1, J2 C37, 86, 0, 0 T40, 84, 0, 1, J3 C70, 92, 1, 0 T75, 90, 0, 1, J4 T5, 90, 0, 1, J5 T44, 55, 0, 1, W4 T74, 58, 0, 4, W5 T68, 58, 0, 4, W6 T71, 58, 0, 4, W9 T87, 63, 0, 4, W10 T65, 58, 0, 4, W11 { Drives: 2 MFM drives supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 HD control connector. J2 Drive 0 data connector. J3 Drive 1 data connector. J4 Floppy connector. J5 LED connector. LED Terminator LED (when on, this LED indicates proper termination). W4 Closed (Default) HD IRQ 14 enabled. Open HD IRQ 14 disabled (when disabling HD contoller). W5 Closed (Default) Floppy DMA ACK 2 enabled. Open Floppy DMA ACK 2 disabled (when disabling floppy controller). W6 Open (Default) Primary HD I/O ports (1F0). Closed Secondary HD I/O ports (170). W9 Open (Default) Primary floppy I/O ports (3F0). Closed Secondary Floppy I/O ports (370). W10 1-2 Floppy controller disabled (also disable W5). 2-3 (Default) Floppy controller enabled. W11 1-2 HD controller disabled (also disable W4). 2-3 (Default) HD controller enabled. } * //EV-348 01 C53, 92, 1, 0 T58, 90, 0, 1, J1 C42, 92, 0, 0 T45, 90, 0, 1, J2 C42, 86, 0, 0 T45, 84, 0, 1, J3 C71, 92, 1, 0 T76, 90, 0, 1, J4 T5, 90, 0, 1, J5 T20, 58, 0, 4, W1 T23, 58, 0, 4, W2 T26, 58, 0, 4, W3 T29, 58, 0, 4, W4 T60, 73, 0, 1, W5 T60, 70, 0, 1, W6 T64, 58, 0, 4, W7 T67, 58, 0, 4, W8 T70, 58, 0, 4, W9 T82, 68, 0, 1, W10 T82, 65, 0, 1, W11 T82, 62, 0, 1, W12 { Drives: 2 ESDI drives supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 HD control connector. J2 Drive 0 data connector. J3 Drive 1 data connector. J4 Floppy connector. J5 LED connector. W1 2-3 (Default) Buffer size = 32KB (do not change). W2 1-2 (Default) Buffer size = 32KB (do not change). W3 2-3 (Default) Buffer size = 32KB (do not change). W4 1-2 (Default) Buffer size = 32KB (do not change). W5 Closed (Default) BIOS address C:8000 - C:BFFF. W6 Closed Open BIOS address C:C000 - C:FFFF. Closed Closed BIOS address D:4000 - D:7FFF. Open Open BIOS address D:8000 - DBFFFF. Open W7 Open (Default) Primary HD I/O ports (1Fx). Closed Secondary HD I/O ports (17x). W8 Closed (Default) HD IRQ 14 enabled. Open HD IRQ 14 disabled (when disabling HD controller). W9 Closed (Default) HD controller enabled. Open HD controller disabled (also disable W8). W10 Closed (Default) Floppy controller enabled. Open Floppy controller disabled (also disable W11). W11 Closed (Default) Floppy DMA ACK 2 enabled. Open Floppy DMA ACK 2 disabled (when disabling floppy controller). W12 Open (Default) Primary floppy I/O ports (3Fx). Closed Secondary floppy I/O ports (37x). } * //EV-349 21 C68, 92, 1, 0 T73, 90, 0, 1, J1 C47, 92, 1, 0 T52, 90, 0, 1, J2 C32, 92, 0, 0 T35, 90, 0, 1, J3 C17, 92, 0, 0 T20, 90, 0, 1, J4 T15, 80, 0, 1, J5 T64, 80, 0, 4, W2 T67, 80, 0, 4, W1 T70, 80, 0, 4, W5 { Drives: 2 ESDI drives supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 Floppy connector. J2 HD control connector. J3 Drive 0 data connector. J4 Drive 1 data connector. J5 LED connector. W1 Open (Default) Primary HD I/O ports (1F0 - 1F7) and primary floppy I/O ports (3F0 - 3F7). Closed Secondary HD I/O ports (170 - 177) and secondary floppy I/O ports (370 - 377). W2 Open (Default) Single-speed floppies installed. Closed Dual-speed floppies installed. W5 Open (Default) Floppy controller enabled. Closed Floppy controller disabled. } * //EV-358 21 C53, 92, 1, 0 T58, 90, 0, 1, J1 C42, 92, 0, 0 T45, 90, 0, 1, J2 C42, 86, 0, 0 T45, 84, 0, 1, J3 C71, 92, 1, 0 T76, 90, 0, 1, J4 T15, 90, 0, 1, J5 T51, 60, 0, 1, SW1 T81, 68, 0, 1, W10 T81, 65, 0, 1, W11 T81, 62, 0, 1, W12 T81, 59, 0, 1, W5 T81, 56, 0, 1, W6 T64, 72, 0, 4, W7 T67, 72, 0, 4, W9 { Drives: 2 ESDI drives supported. 2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB). J1 HD control connector. J2 Drive 0 data connector. J3 Drive 1 data connector. J4 Floppy connector. J5 LED connector. W5 Closed (Default) BIOS address C:8000 - C:BFFF. W6 Closed Open BIOS address C:C000 - C:FFFF. Closed Closed BIOS address D:4000 - D:7FFF. Open Open BIOS address D:8000 - DBFFFF. Open W7 Open (Default) Primary HD I/O ports (1Fx). Closed Secondary HD I/O ports (17x). W9 Closed (Default) HD controller enabled. Open HD controller disabled (also disable W8). W10 Closed (Default) Floppy controller enabled. Open Floppy controller disabled (also disable W11). W11 Closed (Default) Floppy DMA ACK 2 enabled. Open Floppy DMA ACK 2 disabled (when disabling floppy controller). W12 Open (Default) Primary floppy I/O ports (3Fx). Closed Secondary floppy I/O ports (37x). SW1 XXoooooo HD IRQ 11. ooXXoooo HD IRQ 12. ooooXXoo (Default) HD IRQ 14. ooooooXX HD IRQ 15. } *